Post reply

Name:
Email:
Subject:
Message icon:
Bold Italicized Underline Strikethrough | Preformatted Text Left Align Centered Right Align
Insert Image Insert Hyperlink Insert Email Insert FTP Link | Glow Shadow Marquee | Superscript Subscript Teletype | Insert Table Insert Code Insert Quote | Insert Unordered List Insert Ordered List Horizontal Rule | Remove Formatting Toggle View
Smiley Wink Cheesy Grin Angry Sad Shocked Cool Huh Roll Eyes Tongue Embarrassed Lips sealed Undecided Kiss Cry
Verification:
Unregistered users must pass a verification:



Please enter the number from the picture above which is showing FM broadcast antenna:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: Jan
« on: July 27, 2022, 08:58:12 pm »

The RT repetition rate in this device is very close to the recommendations from the original EN50067 standard, to create best balance between different RDS services.

For customized solution, please consider our offer of advanced RDS devices with support of user defined group sequence, dynamic group sequence and much more.
Posted by: ChekAndr
« on: July 27, 2022, 04:30:41 pm »

As I understand it, the sequence is specified in the firmware. Can you change the firmware? (0A, 0A, 2A,2A
 or 0A,0A,2A,2A,2A). It seems to me that this sequence is more suitable for RT radio. :(
Posted by: ChekAndr
« on: July 26, 2022, 09:24:57 pm »

Probably. But 7 seconds is also not enough.
Thank you
Posted by: Jan
« on: July 26, 2022, 09:11:43 pm »

With the group sequence "0A 0A 0A 0A 2A" entire RT is sent out within 7 seconds.

Thus the delay arises somewhere else in the chain. It may be a delay caused by broadcast automation, bad reception, bad RDS level setting or bad receiver.

Posted by: ChekAndr
« on: July 26, 2022, 07:53:27 pm »

I have too much time changing the radio text - 30-60 sec. How to reduce it?
Posted by: Jan
« on: July 26, 2022, 07:35:09 pm »

This device does not support user defined group sequence. The only way is to generate the RDS groups 2A completely by an external application.
Posted by: ChekAndr
« on: July 26, 2022, 07:26:12 pm »

Good day.
Is it possible to change the group sequence 0A 0A 2A 2A 2A using mrdsio.dll?
Posted by: zvykov
« on: February 16, 2022, 03:18:57 pm »

That's what I thought, but just in case, I clarified it. Thank you.
Posted by: Jan
« on: February 16, 2022, 03:00:51 pm »

That's true. The software encoders provide fixed group rates which are optimal for common use or which are given by standards. The setting option would not bring any functional benefit.
Posted by: zvykov
« on: February 16, 2022, 02:12:31 pm »

Quote from: Jan on February 16, 2022, 01:38:19 pm
Other groups may be entered by external application. In such a case, the external application controls the group rate as well.
I use MagicRDS 4 and add RT+ and CT through it. Apparently, the number of groups in this software is also automatically adjusted and does not have manual settings.
Posted by: Jan
« on: February 16, 2022, 01:38:19 pm »

This IC generates only groups 0A and 2A. This group sequence is fixed to 0A 0A 0A 0A 2A which is optimal for typical use.
If User Defined Group 1 is set, the group sequence is fixed to 0A 0A 0A 0A 2A UDG1.
If Radiotext is disabled, the 2A groups disappear from the group sequence.
No other method is available for this IC for controlling the group sequence.

Other groups may be entered by external application. In such a case, the external application controls the group rate as well.
Posted by: zvykov
« on: February 16, 2022, 01:22:32 pm »

Hello, is there a possibility to change the percentage of groups, increase the number of transfers of one and decrease the transfers of the other?